Check that a Persistent Reserve Out CLEAR request:
- clears an existing reservation
- clears existing registration keys
- bumps the PRgeneration number
Signed-off-by: David Disseldorp <ddiss@suse.de>
Confirm that data is consistent across paths when using the atomic
COMPARE AND WRITE operation.
This should be extended in future to issue the requests simultaneously
across both paths, in an attempt to trigger a read/write race.
Signed-off-by: David Disseldorp <ddiss@suse.de>
This test issues a logical unit reset iSCSI TMF request, and then
confirms that all paths report a subsequent unit attention condition.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Write data to device via one path, then read back using a different
path. Confirm that data is correct.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Remove the flags tests for READ* and replace them with a test for the DPO
and FUA bits.
IF the device claims DPOFUA support in modesense then the READ* CDBs
MUST allow these two flags. IF the device does NOT claim DPOFUA then any
READ* CDB with these flags must fail with invalod field in cdb.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Add a test for unmapping a single range of blocks and that
get_lba_status returns correct data.
Test unmapping a single block at offsets 0-255
Test unmapping 1-255 blocks at offset 0 and verify that
get_lba_status at LBA 0 returns a descriptor of 1-255 blocks.
get_lba_status at the last block of the unmapped range returns
a descriptor for a single block.
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Free read_write_buf and task after each test. Free iscsi2 after
each PGR test when using CUnit version 2. Note: CUnit version 1
doesn't support test setup and teardown functions.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Linux distributions like openSUSE 12.3 include CUnit version 2.
Apparently libiscsi uses some CUnit version 1 data structures that
have been modified in CUnit version 2. This causes the libiscsi
build to fail against CUnit version 2. Fix this by detecting the
CUnit version during the configure step.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
REPORT SUPPORTED OPCODES.
Opcodes that are listed in the full list of all supported opcodes as taking
a service action should work to ask reporting option 2 (uses service action)
from but fail when asked for option 1 (no service action)
Similarly, opcodes that are flagged as not taking a service action should
work when used with option 1 but fail with option 2.
Add a simple test that it works or is not implemented.
Add a RCTD test to verify that with this flag clear we get command descriptors without CTDP set and with it set we get command descriptors with CTDP set and a timeout descriptor
If the device does not support PI (INQ->PROTECT) then
verify that PROT_EN, P_TYPE and P_I_EXP are all zero.
If the device does support PI and IF PROT_EN is clear
then verify that both P_TYPE and P_I_EXP are zero.
If the device does support PI and IF PROT_EN is set
then verify that P_TYPE is 0, 1 or 2
Verify that the page length matches up with the size of the data in buffer.
Verify that page length is 0x3c if the device claims SBC-3, and 0x0c if not.
If the device claims SBC-3 and if it claims UNMAP support (LBPU)
then we check that both MAXIMUM UNMAP LBA COUNT and
MAXIMUM UNMAP BLOCK DESCRIPTOR COUNT looks sane.
Sane here means >0, <1M or 0xffffffff
If the device claims SBC-3 and if it does not claim UNMAP support (LBPU)
then we check that both MAXIMUM UNMAP LBA COUNT and
MAXIMUM UNMAP BLOCK DESCRIPTOR COUNT are both 0.
Default to 0 meaning no timeout.
Implement a test for iSCS to test what happens if we send a command
with CMDSN being higher than the target allows.
In this case we dont strictly know what will happen, just that what should
NOT happen is the target responding with success.
But we have to be prepared for any kind of failure, including a timeout,
scsi sense, or even iscsi reject or session failure.
Also test that IF the iSCSI layer provides 2 blocks of DATA-OUT but
the SCSI WRITE* command only covers one single block,
then only the first block will be modified but not the second block.
