In specific situation it might be useful to give up if a reconnect
is not successful or after a given number reconnect retries.
This patch adds the ability to change that. The default remains
the same: retry forever.
Signed-off-by: Peter Lieven <pl@kamp.de>
A storage might sent an R2T response for a WRITE command while
we still sending out the WRITE command PDU. This is especially
the case when the command PDU carries immediata data.
Without this patch the R2T response will get lost as
the cmdpdu for the R2T cannot be found in iscsi_process_pdu()
leading to a deadlock.
Signed-off-by: Peter Lieven <pl@kamp.de>
As part of the test also validate the PDU that libiscsi generates and verify that
1, the PDU we send has the F flag set
2, that datasegmentlength for the PDU is one block
Remove the size field as it is not used. If we would keep it
we would have to calculate it in scsi_task_set_iov_in/out which
would add unneccassry wals to the iovec array.
Signed-off-by: Peter Lieven <pl@kamp.de>
The send logic was completely broken for any cases except
ISCSI_INITIAL_R2T_NO and ISCSI_IMMEDIATE_DATA_YES.
The final flag was set wrong or no data was sent.
It was also broken if the data did not fit into the cmd_pdu as
the consecutive pdus did not have the scsi_cbdata set which
lead to a segfault in iscsi_get_user_out_buffer().
Unfortunately we need to include scsi-lowlevel.h again in iscsi-private.h.
This should be fixed asap by introduction of an iscsi_task struct
to avoid to store iscsi relevant data in the scsi_task.
Signed-off-by: Peter Lieven <pl@kamp.de>
Conflicts:
lib/iscsi-command.c
Signed-off-by: Peter Lieven <pl@kamp.de>
This patch avoid incrementing itt to 0xffffffff which is
a reserved value for immediate pdus. Avoid incrementing
it to 0xfffffff to avoid unexpected behaviour.
Signed-off-by: Peter Lieven <pl@kamp.de>
RFC3720 says that cmdsn comparison must be done using
serial32 arithmetic. This will definetly avoid a deadlock
if cmdsn wraps from 2^32-1 to 0.
Signed-off-by: Peter Lieven <pl@kamp.de>
We can simply next the iscsi_scsi_cbdata in the iscsi_pdu struct
since it is only used inside the iscsi_pdu.
This saves one malloc for each pdu.
Signed-off-by: Peter Lieven <pl@kamp.de>
Change iscsi_scsi_command_async() to write data-out using iovectors
attached to the scsi task structure instead of copying the data into
the buffer holding the header.
Still allow passing the data via an argument to the funtcion so that the
ABI does not change but then just conver the data to an iovector.
Update the write_to_socket functions to know about the iovectors and write them
as part of the pdu.
Convert write10_task to use iovectors.
This will allow 'zero-copy' writes through libiscsi.
However, as 'zero-copy writes does mean that we do more send() calls into
the kernel this may degrade performance for very small i/o.
A scsi write will not take at least 2 send() calls.
One send call for the iscsi header structure and a second send call for the
payload data.
This will be more expensive than the old memcpy() of payload data plus one send() call since the send() will be a lot more expensive than memcpy() of a small amount of data.
This patch defines an scsi_iovec struct which is guaranteed
to be POSIX compatible. It furthermore adds support for
in+out iovectors for bi-directional operations
Signed-off-by: Peter Lieven <pl@kamp.de>
If an application passes buffers to libiscsi for reading they are
currently added to a linked list one by one. This leads to a malloc
for each buffer object plus O(n) walks trough the list to add
the buffer to then end of the list. Additionally the buffer read
routine takes up to O(n) iterations to find the right buffer
for a request.
This patch introduces an scsi_iovector struct to pass buffers to
an scsi task. Adding a new buffer is in O(1) and finding the
right buffer to also. Malloc requirements are in O(log(n)).
Additionally the scsi_iovector struct is itended to be binary
compatible to an QEMUIOVector allowing to pass this structure
directly to the library.
Initial tests have been made booting an Ubuntu LTS 12.04.1
Desktop server up to the login prompt. The following observations
have been made with regards to scsi_malloc calls:
original implementation: ~11.500 mallocs
using iovector instead of list: ~ 7.500 mallocs
passing the iovector directly: 0 mallocs
To enable this feature in qemu for testing the following patch might
be used:
diff --git a/block/iscsi.c b/block/iscsi.c
index a6a819d..2809c15 100644
--- a/block/iscsi.c
+++ b/block/iscsi.c
@@ -390,11 +390,16 @@ iscsi_aio_readv(BlockDriverState *bs, int64_t sector_num,
return NULL;
}
+#if defined(LIBISCSI_FEATURE_IOVECTOR)
+ assert(sizeof(struct QEMUIOVector) == sizeof(struct scsi_iovector));
+ scsi_iovector_assign(acb->task, (struct scsi_iovector*) acb->qiov);
+#else
for (i = 0; i < acb->qiov->niov; i++) {
scsi_task_add_data_in_buffer(acb->task,
acb->qiov->iov[i].iov_len,
acb->qiov->iov[i].iov_base);
}
+#endif
iscsi_set_events(iscsilun);
---
Signed-off-by: Peter Lieven <pl@kamp.de>
Split the INQUIRY data-in unmarshalling into smaller chunks, fixing some
potential memory leaks along the way.
Signed-off-by: Arne Redlich <arne.redlich@googlemail.com>
